16x16mm Flexible Wall Washer: Confirm Single-Color Control and Module Length Before Ordering
Quick decision
Specify this evidence set as a single-color architectural line unless a separate signed version proves a control IC and protocol. Choose finished module length from the façade grid, calculate module and joint quantities, then request voltage and power before any electrical release.
Published facts and evidence boundary
| Parameter | Published or derived value |
|---|---|
| Published model | L-W-10048-1616-2835 |
| Light source | Single color; SMD2835 package |
| Body and density | 16x16mm silicone body; 48 LEDs/m |
| Finished lengths | 0.5m, 1m, 1.5m and 2m |
| Other length wording | Separate entry states length not above 5m |
| Protection/electrical gap | IP67 listed; voltage and power not confirmed in current evidence |
Decide whether the façade needs an even wash or pixel animation
The confirmed source is single color, so the defensible design target is a consistent architectural line or wash. The page also uses pixel-pitch wording, but that phrase alone does not establish individually addressable sections or RGB animation.
Approve a lit sample against the real wall material and offset. Review beam placement, shadowing at corners and brightness continuity across one joint. If the design brief needs animated pixels, stop and qualify a separately documented control version.
Read 2835 as the LED package, not as a control protocol
The published model L-W-10048-1616-2835 combines a 16x16mm silicone body, 48 LEDs/m and single-color wording. Although one data row places 2835 beside an IC label, SMD2835 identifies the LED package and does not prove a control IC.
The purchase row should state emitted color or CCT, dimming method, voltage, watts/m, beam version, module length, cable exit, connector and IP67 construction. Do not add DMX, SPI or pixel addresses until the exact ordered version provides that evidence.
Use module arithmetic to expose joint and spare quantities
At 48 LEDs/m, nominal counts are 24 LEDs in 0.5m, 48 in 1m, 72 in 1.5m and 96 in 2m. For a 12m straight line, 2m modules require six modules and five inter-module joints; 1m modules require twelve modules and eleven joints.
That comparison helps purchasing and maintenance, but it is not a power calculation. Because the current evidence does not confirm voltage or watts/m, do not estimate current, feed distance or driver capacity. Obtain those values from the signed production drawing and verify loaded end voltage on the sample branch.
Keep module length, cut unit and control identity separate
The page lists finished lengths of 0.5m, 1m, 1.5m and 2m, plus another entry stating length not above 5m. None of those values proves a field cut interval, maximum electrical run or pixel zone length.
Order finished sections to the elevation schedule and document how corner pieces and field joints are made. For single-color dimming, freeze driver or dimmer type and wiring. For addressable behavior, require a different signed record naming IC, protocol, zones/m and addressing workflow.
Treat the 16x16mm body and IP67 joints as one installation boundary
The 16x16mm silicone body affects channel clearance, clips, corner routing and cable exit. No minimum bend radius is published in the current evidence, so a physical corner sample is safer than borrowing a radius from another wall-washer family.
IP67 on the product row does not automatically cover cut ends, connectors, cable penetrations or water traps. Freeze the exact end cap, injection seal, clip spacing, drainage orientation and replacement method on the approved sample.
Conditional project decision table
| Project condition | Decision and evidence |
|---|---|
| Continuous single-color line | Use the signed CCT/color and check uniformity across a real joint. |
| Animated pixel façade | Do not use this evidence alone; qualify a version with named IC and protocol. |
| Protected interior feature | Choose module length for the grid and keep joints serviceable. |
| Outdoor façade | Specify IP67 body plus documented ends, connectors and drainage. |
| 12m straight elevation | Compare six 2m modules/five joints with twelve 1m modules/eleven joints. |
| Central dimming or show control | Freeze voltage, driver/dimmer method and circuit grouping before release. |
LIKELIGHT L-W-10048-1616-2835 as the single-color project case
This product fits façade details that need a compact 16x16mm flexible silicone wash line, 48 LEDs/m, IP67 wording and selectable finished lengths. The modular options let the designer trade fewer joints against easier handling and replacement.
It is not evidence of a native pixel-control system. LIKELIGHT should issue a signed order drawing with color, voltage, power, beam, exact length, connector and sealing construction before the façade schedule is frozen.
Information required before quotation
- elevation with each straight and corner length
- single color/CCT and target visual effect
- wall material, offset and viewing distance
- chosen 0.5m/1m/1.5m/2m module schedule
- required voltage, watts/m and dimming method
- IP67 exposure, drainage and joint location
- cable exit, connector, lead and mounting detail
- sample quantity, project metres, spares and delivery date
These inputs decide the control identity, finished-section schedule, joint count and electrical evidence together. They prevent the words pixel pitch from turning a single-color product into an unsupported addressable specification.
Frequently asked questions
Does 48 LEDs/m mean 48 addressable pixels/m?
No. It is a physical LED density; no addressable grouping is confirmed.
Is SMD2835 a control IC?
No. It is the LED package designation in this product evidence.
How many joints are in a 12m line using 2m modules?
Six modules create five inter-module joints when installed end to end.
Can power be calculated from this page?
Not safely. Voltage and watts/m are not confirmed in the current evidence.
