Published Product Parameters

Engineering Design Review

Use the published data below as a design input register, not as a substitute for a project release. Every item that affects interchangeability, safety or visual effect must be tied to the approved sample, wiring drawing and bill of materials.

Controller, Addressing and Signal Topology

Do not select a controller from the product appearance alone. The production configuration must define the exact IC or protocol, pixel grouping, controller port capacity, data direction, start address, channel order, connector pinout and termination method. Create a port-by-port address schedule before installation. Where a long chain is planned, validate the actual data path with the approved cable, controller and effect file rather than assuming the maximum chain length.

For this item, the published control basis is No addressable control IC is published; 2835 is listed as the LED source. Any alternate IC, RGB/RGBW arrangement, pixel pitch or customized cable must be treated as a new control configuration and confirmed before production.

Power Distribution and Voltage-Drop Plan

The published electrical basis is To be confirmed from the approved production configuration at To be confirmed from the approved production configuration, with a planning current of To be calculated after voltage and power are confirmed. Calculate power supplies from the final quantity and simultaneous full-output scene, then reserve engineering margin in the selected supply. Define feed locations, branch lengths, wire gauge, fuse or protection points and return path on the installation drawing.

Measure voltage at the first and last load during a full-output commissioning scene. A colour shift, brightness difference or controller reset is a system-level issue that must be corrected by the distribution plan, not by changing the effect file.

Optical, Mechanical and Environmental Boundary

The published optical / structural configuration is single-colour SMD2835 silicone-body linear light, 48 LEDs/m, in the format 16 x 16 mm; 0.5 m, 1 m, 1.5 m or 2 m sections; total length no more than 5 m. Confirm viewing distance, pixel spacing, mounting pitch, cable exit direction, bend or support condition, service access and the interface to the supporting structure. These decisions control the final visual uniformity and maintenance access.

The published protection target is IP67. For outdoor or wet installations, verify the complete installed system: housing, gland, connector mating, end treatment, mounting orientation, drainage and field joints. A fixture rating alone does not validate an unsealed field connection.

Factory Acceptance and Site Commissioning

Before shipment, verify the approved channel order, addressing, full-load current, programmed test pattern, connector continuity and visible output against the released sample. At site, inspect polarity before energizing, commission one controller port at a time, record the final address map, then run a sustained full-output and programmed-effect test.

Acceptance should include visual consistency at the intended viewing distance, correct scene playback, stable communication, supply voltage under load, connector inspection and a documented replacement / service method. Keep the approved sample, drawing revision and controller file with the project record.

OEM Order Freeze Checklist

• Final model, LED colour configuration, IC / protocol and pixel grouping.
• Working voltage, power distribution drawing, cable length and connector pinout.
• Physical dimensions, spacing, mounting interface and cable exit direction.
• Target IP construction including ends, joints and outdoor installation orientation.
• Controller model, effect file, address map, sample approval and acceptance method.

Product-Specific Control Note

Der angegebene Steuer-IC oder die Option ist No addressable control IC is published; 2835 is listed as the LED source. Er bestimmt die Adressierung der Effekte. Finalen IC, Protokoll, Controllerausgang, Datenrichtung, Pinbelegung und Adressplan gemeinsam bestatigen; ahnliche Leuchten konnen im System inkompatibel sein.

Product-Specific Installation Note

Die angegebene Schutzoption ist IP67. Endausfuhrung, Kabelaustritt, Stecker, Endabschluss, Montageflache und Feldverbindungen bestatigen. Die Lichtstruktur ist single-colour SMD2835 silicone-body linear light, 48 LEDs/m; Freiraum, Warmeweg und Montageplan mussen freigegeben werden.

Application Fit

Die Produktseite nennt Anwendungen wie outdoor flexible linear wall washing and architectural outline lighting. Endkonfiguration nach dem realen Standort, nicht nur nach dem Produktnamen auswahlen.

FAQ

Ist Anpassung moglich? Elektrische Konfiguration, Masse oder Abstand, Kabel, Stecker, IP, Controller-Kompatibilitat und Menge vor Produktion bestatigen.